Modernization of Milk Packaging as a Result of Replacing Aluminum Foil with Metallized Polyethylene
https://doi.org/10.36107/hfb.2019.i2.s257
Abstract
This paper discusses the possibility of modernizing the production technology of combined packaging polymer materials used for packaging milk and dairy products. Multilayered and combined film materials consist of layers of low-density polyethylene and paper, sometimes combined with layers of aluminum foil or aluminum-metallized paper. Experiments on the possibility of replacing foil or metallized paper with metallized polyethylene should be considered as a promising research trend. Metallized films are cheaper than aluminum foil, and have a number of technological and operational advantages such as less weight, reduce or even eliminate damage to the layers when the material bends or deformations of the package. In addition, replacing the foil with metallized polyethylene increases the level of adhesive interaction between the layers of the combined material. At the same time, the costs of manufacturing this kind of material not only do not increase, but also can even be significantly reduced. Experimental studies and tests of the obtained samples had shown that combined materials based on metallized films have a lower defect rate compared to foiled materials. Experimental studies and tests of the obtained samples had shown that combined materials based on metallized films have a lower defect rate compared to foiled materials. This improves a number of films’ properties -reduces their permeability to gases (for most food products, this indicator is important for oxygen) and water vapor, reduces the number of through holes, while increasing the strength indicators, and reduces the consumption of materials for packaging.
About the Authors
V. V. Ananyev
Moscow Polytechnic University
Russian Federation
Russian Federation
Vladimir V. Ananyev
38 Bolshaya Semyonovskaya str., Moscow, 107023
A. O. Bannikova
Moscow State University of Food Production
Russian Federation
Russian Federation
Olga A. Bannikova
11 Volokolamskoe highway, Moscow, 125080
A. Alkheer
Moscow Polytechnic University
Russian Federation
Russian Federation
Ali Alkheer
38 Bolshaya Semyonovskaya str., Moscow, 107023
References
1. Ananyev V. V., Bannikova, O. A., Beznaeva, O. V., Chalykh, A. E., Stepanenko, V. Yu., Petrova, T. F. (2019). Improving the quality of combined packaging materials by ultrasonic processing. Klei. Germetiki. Tekhnologii [Glues. Sealants. Technologies], 9, 21-26.
2. Aksenova, T. I., Ananyeva, V. V., Dvoretskaya, N. M., Ivanova, T. V., Lyubeshkina, E. G., & Rozantsev, E. G.(2009). Tara i upakovka [Containers and packaging]. Kolos.
3. Bannikova, O. A. (2012). Vliyanie tekhnologicheskih parametrov processa ekstruzionnogo laminirovaniya na svojstva kombinirovannogo materiala «polietilen-bumaga» [Influence of technological parameters of the extrusion lamination process on the properties of the combined material “polyethylene-paper”] [Candidate dissertation]. Moscow.
4. Beznaeva, O. V. (2014). Antimikrobnaya upakovka na osnove fizicheski modificirovannyh plenochnyh materialov [Antimicrobial packaging based on physically modified film materials] [Candidate dissertation]. Moscow.
5. Bleisch, G. (2010). High-quality packaging and production process. Molochnaya promyshlennost [The dairy industry], 6, 18-19.
6. Zagidullin, A. I., Garipov, R. M., Khasanov, A. I., Grigoriev, A. Yu., & Kozlov, A. A. (2015). Influence of welding parameters on the barrier properties of the weld of heat-shrink multilayer films. Vestnik Teh nologicheskogo universiteta [Bulletin of the Technological University], 18(7), 111-114.
7. Zelke, S., Kutler, D., & Hernandez, R. (2011). Plastikovaya upakovka [Plastic packaging]. Professiya.
8. Zuev, B. M., Zuev, M. B., Ulitin, N. V., Deberdeev, R. Ya., & Deberdeev, T. R. (2012). Determination of optical and mechanical properties of polymers. Plasticheskie massy [Plastic masses], 7, 7-9.
9. Kirsh, I. A., Frolova, Yu. V., Beznaeva, O. V., Pomogova, D. A., & Tikhomirov, A. A. (2017). Creation of packaging polymer materials with antimicrobial properties. University news. Izvestiya vuzov. Prikladnaya himiya I biotehnologiya [Applied chemistry and biotechnology], 7, 3(22), 145-152.
10. Lokshin, M. Z., Makarov, G. S., & Sirotinsky, M. S. (2002). Current issues of production and application of aluminum for packaging. Tsvetnyie metally [Non-ferrous metals], 12, 47-55.
11. Serova, V. N. (2014). Influence of metallization and priming of polyethylene terephthalate packaging film on the quality of the colorful layers applied to it by flexographic printing. Vestnik Tehnologicheskogo universiteta [Bulletin of the technological Universit], 17(12), 65-68.
12. Serova, V. N. (2015). Influence of aluminum oxide nanocoating on the properties of polyethylene terephthalate packaging film and printing ink applied to it. Klei. Germetiki. Tekhnologii [Glues. Sealants. Technologies], 8, 36-41.
13. Serova V. N. (2016). Noskova E. N. Optical characteristics and light resistance of polymer packaging films and applied colorful layers. Vestnik Tehnologicheskogo universiteta [Bulletin of the technological Universit], 19(15), 61-63.
14. Fedotova, O. B. (2007). The role of packaging in the dairy industry. Molochnaya promyshlennost [The dairy industry], 5, 4-6.
15. Fedotova, O. B., Makarkin, D. V., Sokolova, O. V., & Dunchenko, N. I. (2019). Development and research of the nutritional and biological value and consumer properties of a gluten-free fermented milk product with flour. Voprosy pitaniya [Questions of nutrition], 88(2), 101-110.
16. Shalygina, A. M., & Kalinina, L. V. (2007). Obshchaya tekhnologiya moloka i molochnyh produktov [General technology of milk and dairy products]. Kolos..
17. Anan’ev, V. V., Bannikova, O. A., & Chalykh, A. E. (2011). Adhesion properties of a paper (carboard)-polyethylene combined material obtained by the extrusion laminator method. part 2. International Polymer Science and Technology, 38(9), 9-10. doi: 10.1177/0307174X1103800903
18. Alvarez, V. B., & Pascall, M. A. (2011). Packaging. In Encyclopedia of Dairy Sciences (Second Edition) (pp.16-23). https://doi.org/10.1016/B978-0-12-374407-4.00387-3
19. Bayus, J., Ge, Ch., & Thorn, B. (2016). A preliminary environmental assessment of foil and metallized film centered laminates. Resources, Conservation and Recycling, 115, 31-41 https://doi.org/10.1016/j.resconrec.2016.08.024
20. Bishop, Ch. A., & Mount, E. M. (2016). Vacuum metallizing for flexible packaging. In John R. Wagner, Jr. (Ed.), Multilayer Flexible Packaging (Second Edition), 15, 235-255. https://doi.org/10.1016/B978-0-323-37100-1.00015-6
21. Chalykh, A. E., & Zlobin, V. B. (1988). Modern Ideas About Diffusion in Polymer Systems, Russian Chemical Reviews, 57(6), 504–519. https://doi. org/10.1070/RC1988v057n06ABEH003367
22. Coles, R., McDowell, D., & Kirwan., M. J. (2009). Food Packaging Technology. Packaging technology series. Wiley.
23. Goydan, R., Carroll, T. R., Schwope, A. D., & Gruenfeld, M. (1990). Evaluation of Polyester and Metallized-Polyethylene Films for Chemical Protective Clothing Applications. Plastic Film and Sheeting, 6(2), 106-116. https://doi.org/10.1177/875608799000600204
24. Gupta, S., Dixit, M., Sharma, К., & Saxena, N. S. (2009). Mechanical study of metallized polyethylene terephthalate (PET) films. Surface and Coatings Technology, 204(5), 661-666. https://doi.org/10.1016/j.surfcoat.2009.08.051
25. Haidara H., Vallat M. F., Schultz J., & Lutgen P. (1990). Films polymeres metallises: Mesure de l’adhesion polymere-metal [Metallized polymer films: Measurement of polymer-metal adhesion]. European Polymer Journal, 26(8), 907-910. https://doi.org/10.1016/0014-3057(90)90166-2
26. Jang W., Rawson I., & Grunlan J. C. (2008). Layer-by-layer assembly of thin film oxygen barrier. Thin Solid Films, 516(16), 4819-4825.
27. Klaiman, К., Ortega, D. L., & Garnache, C. (2016). Consumer preferences and demand for packaging material and recyclability. Resources, Conservation and Recycling, 115, 1-8.
28. Kerry, J. (2012). 9: Aluminium foil packaging. Packaging Technology. Woodhead Publishing Limited. .48 https://doi.org/10.1533/9780857095701.2.163
29. Manfredi, M., Fantin, V., Vignali, G., & Gavara, R. (2015). Environmental assessment of antimicrobial coatings for packaged fresh milk. Journal of Cleaner Production, 9515, 291-300. doi: 10.1016/j.jclepro.2015.02.048
30. Michele S. Pinto, M. S., Pires, A. S. P., Sant’Ana, H. M. P., Soares,N. F. F., & Carvalho, A. F. (2014). Influence of multilayer packaging and microfiltration process on milk shelf life. Food Packaging and Shelf Life, 1, 151-159. https://doi.org/10.1016/j.fpsl.2014.01.006
31. Madhusudan, P., Chellukuri, N., & Shivakumar, N. (2018). Smart packaging of food for the 21st century – A review with futuristic trends, their feasibility and economics. Materials Today: Proceedings, 5(10), 1, 21018-21022. https://doi.org/10.1016/j.matpr.2018.06.494
32. Robertson, G. L. (2016). Food Packaging: Principles and Practice. Third Edition. CRC Press.
33. Sidwell, J. (2007) Chemical migration from multi-layer packaging into food. In book: Chemical Migration and Food Contact Materials (pp.346-370). Rapra Technology. https://doi.org/10.1533/9781845692094.3.346
Review
For citations:
Ananyev V.V., Bannikova A.O., Alkheer A. Modernization of Milk Packaging as a Result of Replacing Aluminum Foil with Metallized Polyethylene. Health, Food & Biotechnology. 2019;1(2):41-51. (In Russ.) https://doi.org/10.36107/hfb.2019.i2.s257
Views:
354
Email this article 